INSTRUCTIONS PERTAINING TO A RISK OF FIRE,OR INJURY TO PERSONS
IMPORTANT SAFETY INSTRUCTIONS
Lighted lamp is HOT!
WARNING — To reduce the risk of FIRE OR INJURY TO PERSONS.
1) Turn off / unplug and allow to cool before replacing lamp.
2) Lamp gets HOT quickly! Contact only switch / plug when turning on.
3) Do not touch hot lens or cowl.
4) Do not remain in light if skin feels warm. (Light is intense, it may cause “sunburn”.)
5) Do not look directly at lighted lamp.
6) Keep lamp away from materials that may burn.
7) Use only with wattage and lamp marked on fixture.
8) Do not touch the inner glass envelope of the lamp at any time. Use a soft cloth. Oil from skin may damage lamp.
9) Do not operate the fixture with a damaged or missing lens.
SAFETY INSTRUCTIONS
READ THIS FIRST
KEEP THESE INSTRUCTIONS
This fixture is intended for installation in accordance with the National
Electric Code (NEC) and Local code specifications. Failure to adhere to
these codes and instructions may result in serious injury and/or property damage and will void the warranty.
1) WARNING:
This fixture is not to be installed within 10 feet (3M) of a pool, spa or fountain.
2) This fixture is to be used only with a power unit (transformer) rated a maximum of 300 W (25 AMPS) 15 volts.
3) According to the requirements of the National Electric Code (NEC), direct
burial rated wire is to be buried a minimum of 6" [152mm] beneath the surface of the ground.
NOTE:
If additional Direct Burial wire is needed, contact your local Kichler
®
landscape distributor.
• 8 GA wire can be purchased in length of 250’ (76 M), 15503-BK.
• 10 GA wire can be purchased in length of 250’ (76 M), 15504-BK.
• 12 GA wire can be purchased in lengths of 100’ (30 M), 15501-BK; 250’ (76 M), 15502-BK; 500’ (152M), 15505-BK; and 1000’
(304 M), 15506-BK.
4) Fixture shall not use a tungsten halogen lamp unless the fixture is marked for use with such lamps.
5) Wiring connections must be made with approved/listed wire connection device(s) suitable for the application. Do not exceed
manufacturers’ wiring combination specifications for size and quantity of conductors.
CAUTION
WHEN INSTALLING KICHLER LANDSCAPE LIGHTING (LINE VOLTAGE OR LOW VOLTAGE), CARE SHOULD BE TAKEN TO KEEP CLEAR OF POTENTIALLY
COMBUSTIBLE MATERIALS.
WHEN MAINTAINING THE FIXTURES, BE SURE TO REMOVE LEAVES, PINE NEEDLES, GRASS CLIPPINGS, MULCH, OR ANY DEBRIS THAT HAS ACCUMULATED
ON THE LIGHT BULB, LENS, OR BODY OF THE FIXTURE.
ASSEMBLY AND INSTALLATION
1) Determine desired location for fixture and dig hole. Hole should be approximately 6" (152mm) in diameter and 10" (254mm) deep.
2) Fill bottom of hole with approximately 3" (76mm) of pea gravel.
3) Remove screws from top of fixture then remove cap, glass and yoke assembly.
4) For installation of incandescent lamp: Assemble rubber clips to yoke with groove at top facing center. Rubber clips should be
equally spaced.
For installation of LED lamp: Assemble rubber clips to yoke. The thicker end of each rubber clip should be facing up. This will
allow for proper seating of the LED lamp. Rubber clips should be equally spaced.
5) Connect wires to contacts on back of bulb and snap bulb into rubber clips.
6) Insert yoke assembly with bulb into fixture. Gasket around top of yoke assembly should be inspected to insure it is clean and free
of debris.
7) Place glass and cap on top of fixture and secure in place with screws.
8) Lay fixture in hole and backfill around the fixture with soil.
9) Make wire connections using supplied Kichler
®
Pro Series Wire Connectors following instructions included, or using other
approved wiring connection method (not supplied.)
Date Issued: 2/20/15
IS-15194-US
For warranty information please visit: http://www.landscapelighting.com/portal/warranty_page
Para informacion de la garantia por favor visite: www.landscapelighting.com/portal/warranty_page
We’re here to help
866-558-5706
Hrs: M-F 9am to 5pm EST
