Top Assembly
Shared End Panel
Right End Panel
Base Assembly
Glides
Left End Panel
2" Hex Head Bolts
with Lock Washers
and Flat Washers
4
1
/
2
" Hex Head Bolts
with Lock Washers
and Flat Washers
S
Figure 4
Flat Washer
and Hex Nut
Tools Required:
•
#2 Phillips screwdriver
•
1
/
2
" socket
•
Socket wrench
Hardware Included:
•
#8 x
5
/
8
" screws
•
#8 x 1
1
/
4
" screws
•
#10 x 1
1
/
2
" pan head screws
•
5
/
16
" x 2" hex head bolt
•
5
/
16
" x 4
1
/
2
" hex head bolt
•
5
/
16
" lock washer
•
5
/
16
" flat washer
•
5
/
16
" hex nut
•
Metal pegs
1. Set back edge of left end panel on flat
surface (holes to inside – if it’s a
curved end panel make sure the
curved edge is up).
2. Align the side holes in the base
assembly with the lower holes in the
left end panel. Insert 2" hex head bolts
with lock washers and flat washers into
the base and end panel (Figure 1).
3. Align the side holes in the top
assembly with the upper holes in the
left end panel (Figure 2). Make sure
the faceplate on the top assembly is to
the front and that the back panel
groove is to the back. Insert 2" hex
head bolts with lock washers and flat
washers into the top assembly and
end panel. Tighten.
4. For single starter unit (stand-alone)
and final end panel for connecting
units: Take the right end panel (holes
to inside) and align the side with the
holes in both the base and the top
assembly (Figure 3). Insert 2" hex
head bolts with lock washers and flat
washers into the base and top
assembly. Tighten.
5. For adder units (connecting) – Align
the side holes in the shared panel
(holes both sides) with the holes in
both the base assembly and the top
assembly. Insert 4
1
/
2
" hex head bolts
with lock washers, flat washers and
nut into the base assembly. Do not
tighten (Figure 4).
6. Align the side holes in both the base
and top assembly with the side holes
in the right end panel. Insert 2" hex
head bolts with lock washers and flat
washers into base assembly and top
assembly (Figure 4).
7. Tighten all 2" and 4
1
/
2
" hex head bolts.
Left End Panel
2" Hex Head Bolts
with Lock Washers
and Flat Washers
Base Assembly
Base Assembly.eps
Figure 1
Left End Panel
2" Hex Head Bolts
with Lock Washers
and Flat Washers
Base Assembly
Top
Assembly
Top Asm.eps
Figure 2
Right End Panel
Rt. End Pnl Install.eps
Glides
Figure 3
Left End Panel
2" Hex Head Bolts
with Lock Washers
and Flat Washers
Base Assembly
Top Assembly
Assemble units as described herein only. To do otherwise
may result in instability. All screws, nuts and bolts must
be tightened securely and must be checked periodically
after assembly. Failure to assemble properly, or to secure
parts may result in assembly failure and injury.
1330 Bellevue Street • P.O. Box 8100 • Green Bay, WI 54308-8100 • Tel 1-800-424-2432 • www.ki.com
© 2008 KI All Rights Reserved • Litho in USA. • Code KI-61564R3/TMI/PDF/1209
Figure 1
Assembly Instructions
CrossRoads
®
Newspaper Display Unit
December 2009
Figure 2
Figure 3
Figure 4
