background image

38

Transit

NOTE: The new backrest assembly, standard and transit, uses new backrest tubes. If the chair does 
not already have the new backrest design, new backrest tubes are needed as the old tubes are not 
compatible.

1.   Remove any cushion or seating components that may be in the way of the current backrest removal. 

Also, remove any backrest tubes and/or handles that may be used after the backrest installation 
process.

NOTE: Refer to parts manual for additional information on compatibility restrictions for the new 
backrest design.

2.   There are two types of backrests. Use the image below to determine the version you have. For an 

original backrest, remove three bolts (E, F & I), three saddles (C & J), four washers (B, H & L) and three 
nuts (A, K & M) from back plate (D) to remove the back post using a 4mm Allen wrench, an 8mm 
wrench and a 10mm wrench. Twist off the cable housing to detach cable from back plate. Repeat on 
opposite side. For a new backrest, remove three bolts (E & F), one washer (B), four saddles (C & H), one 
saddle back (G) and three nuts (A & I) using a 4mm Allen wrench, a 5mm Allen wrench, an 8mm wrench 
and a 10mm wrench. Remove the screw (D) from the backrest release bar using a Phillips screwdriver 
and repeat on opposite side.

3.   Install new backrest by installing pivot (F) into new backrest tubes and securing with bolt (E), back plate 

(D), two saddles (C), washer (B) and nut (A) using a 5mm Allen wrench and an 8mm wrench. Repeat on 
opposite side.

A

B

C

D

C

E

F

G

H

I

J

B

K

L

M

A

B

C

C

D

E

F

F

G

H

H

I

I

Original Backrest Design

New Backrest Design

A

B

C

C

E

D

F

Содержание Rogue and Rogue XP





































































Отзывы: