Ki Mobility Rogue and Rogue XP Скачать руководство пользователя

Страница: 58 / 68

Reversing Wheel Lock

5. Reinstall the wheel lock assembly onto the wheel lock bar. For a low profile scissor lock, use a 5mm

Allen wrench to install the two bolts. For the other three wheel locks, install hardware using a 4mm
Allen wrench and a 10mm wrench. See image below.

NOTE: Always tighten wheel lock hardware by alternating between the two bolts while tightening a
little at a time. This prevents overclamping on one set of hardware which can lead to binding of the
fasteners and increased difficulty in removal.

6. Test the wheel locks. Ensure wheel lock arms embed in tires at least 1/8 inch when locked. If they do

not embed at least 1/8 inch, readjust wheel lock and test again.

Low Profile
Scissor Lock

Short Thro
Scissor Lock

Push to Lock Flush
Mount Wheel Lock

Push and Pull to Lock
Wheel Locks

Содержание Rogue and Rogue XP





































































Результаты поиска

Содержание Rogue and Rogue XP

Отзывы:

Похожие инструкции для Rogue and Rogue XP

Бренды по названию

Популярные бренды

Ki Mobility Rogue and Rogue XP, Техническое руководство

Результаты поиска

Содержание Rogue and Rogue XP

Отзывы:

Похожие инструкции для Rogue and Rogue XP

Бренды по названию

Популярные бренды