Keysight N9923A Скачать руководство пользователя страница 79

Страница: 79 / 276

Keysight N9923-90001 User’s Guide

CAT (Cable and Antenna Test) Mode
CAT Mode Settings

—

Left

The Settings table is shown to the left of the trace window

—

Bottom

The Settings table is shown below the trace window

— When finished changing ALL settings, press

Done

to save your settings

Frequency Range

Set the range of frequencies over which you would like to make CAT Mode
measurements

When the frequency range is changed after a calibration is performed, the cal
becomes interpolated. Learn more in

“Interpolation *” on page 119

How to set Frequency Range

— Press

Freq/Dist

— Then choose from the following

—

Start

and

Stop

frequencies - beginning and end of the sweep.

—

Center

and

Span

frequencies – the center frequency and span of

frequencies (half on either side of center).

— Follow each setting by entering a value using the numeric keypad,

arrows, or the rotary knob.

—After using the keypad, select a multiplier key. Learn about multiplier

abbreviations in

“Multiplier Abbreviations” on page 34

—After using the

arrows or the rotary knob, press

Enter

. The

amount of frequency increment is based on the current span and can
NOT be changed in CAT Mode.

Scale Settings

Adjust the Y-axis scale to see the relevant portions of the data trace. The Y-axis
is divided into 10 graticules.

This setting can be changed at any time without affecting calibration accuracy.

How to set Scale

— Press

Scale / Amptd

— Then choose from the following three methods:

Autoscale All

Autoscales all of the traces on the screen, useful only

for dual-trace configurations.

2. Set Scale, Reference Level, and Reference Position:

—

Scale

Manually enter a

scale per division

to view specific

areas of the trace

Содержание N9923A





















































































































































































































































































Результаты поиска

Содержание N9923A

Отзывы:

Keysight N9923A, Руководство пользователя, Страница: 79 / 276

Результаты поиска

Содержание N9923A

Отзывы: