Keysight N9923A Скачать руководство пользователя страница 243 | Manualshive

Страница: 243 / 276

Keysight N9923A Скачать руководство пользователя страница 243

Keysight N9923-90001 User’s Guide

243

Working with the Lithium-Ion Battery
Charging the Battery

Using the External Battery Charger (N9910X–872)

Figure 16-2

External Battery Charger (N9910X-872)

The external battery charger (N9910X–872), lets you charge a fully depleted
battery in approximately three hours. It is a two bay, level–3 stand-alone
battery charger that is compliant with the standard Smart Battery System. The

two bays are charged sequentially on a first-come, first-served basis, though a
discharge can be performed in the left bay while the right bay is charging.

For more information, refer to the Instruction Manual included with the

external battery charger.

Read the safety information in

“For the External Battery Charger

(N9910X-872)” on page 251

External Battery Charger LED

Charging Status

Green

Fully charged

Green flashing

Fast charging

Yellow flashing

Reconditioning – the accuracy of the

battery’s internal LED charge gauge

is being renewed. See

“Reconditioning Battery” on

Yellow/green

Battery is reconditioned

Red flashing

Error

Yellow

Standby

«
...
241
242
243
244
245
...
»

Содержание N9923A





















































































































































































































































































Отзывы:

Нет отзывов