manualshive.com logo in svg

Keysight N9923A, Руководство пользователя, Страница: 251 / 276

Поделиться
Скачать
Keysight N9923A Скачать руководство пользователя страница 251

Keysight N9923-90001 User’s Guide

                                                                                                                      251

Safety Considerations
For the External Battery Charger (N9910X-872)

For the External Battery Charger (N9910X-872)

For the Battery

Lithium battery packs may get hot, explode, or ignite and cause serious injury if 
exposed to abuse conditions. Be sure to follow these safety warnings: 

The AC/DC adapter is for indoor use only.

Never use a modified or damaged charger. Use the original AC–DC 

adapter ONLY.

The AC/DC adapter is designed for use in Installation Category II and 

Pollution Degree 2 per IEC 61010-1.

If charging batteries externally, use the optional external charger available 

from Keysight, or another SMBus charger of level II or higher.
Never use a non–SMBus charger because the battery issues commands 

over the SMBus to the charger to control the charge rate and voltage.
Never use a modified or damaged charger.

External AC/DC power 

supply, U.S. FCC 

compliance

Meets the required verification equipment authorization rules.
This device complies with part 15 of the FCC Rules. Operation is subject to the following two 

conditions: (1) This device may not cause harmful interference, and (2) this device must accept 

any interference received, including interference that may cause undesired operation.

Lithium–ion batteries:

—

Must not be exposed to high temperatures (>70°C) or fire.

—

Must be kept away from children.

—

Must not be short circuited.

—

Must be replaced only with Keysight qualified Li–ion batteries.

—

If replaced or charged improperly, there is a danger of explosion.

Do not connect the positive terminal and negative terminal of the 

battery to each other with any metal object (such as wire).

Do not carry or store the battery with necklaces, hairpins, or other 

metal objects.

Содержание N9923A





















































































































































































































































































Отзывы:

Нет отзывов