Keysight N9923A Скачать руководство пользователя страница 148

Страница: 148 / 276

148 Keysight N9923-90001 User’s Guide

Pulse Measurements Mode – Option 330
Pulse Measurement Settings

Pulse Measurement Settings

Select Pulse Measurement Mode before making any setting in this section.

How to select Pulse Measurement Mode

— Press

Mode

— Then

More

if your FieldFox contains more than five measurement modes.

— Then

Pulse Measurements

Measurement Selection

The pulse measurement results are presented as either a traditional power
meter display or as a trace graph.

How to select the Measurement

— Press

Measure 1

— Then choose from the following:

—

Average

Average power (Meter display)

—

Peak

Peak power (Meter display)

—

Pk to Avg

Displays the difference between the above two

measurements (Meter display)

—

Trace Graph

(default) The primary trace (Tr 1) plots pulse data in

amplitude versus time. Optionally, you can enable a secondary
‘zoom’ trace. Learn how in

“Zoom Window” on page 149

When a ‘Meter display’ measurement is selected, the following Pulse
Measurement Mode settings are identical to the standard USB Power

Meter Mode settings.

— Learn how to set

Scale

“Scale” on page 150

— Learn how to set

Relative and Offset Power

“Relative and Offset

Power Measurements” on page 131

— Learn how to set

Display Units

“Display Units” on page 131

— Learn how to set

Limits

“All about Limit Lines” on page 185

Frequency / Time

How to set Frequency

— Press

Freq/Dist

— Then choose from the following:

Содержание N9923A





















































































































































































































































































Результаты поиска

Содержание N9923A

Отзывы:

Keysight N9923A, Руководство пользователя, Страница: 148 / 276

Результаты поиска

Содержание N9923A

Отзывы: