Keysight N9923A Скачать руководство пользователя страница 149

Страница: 149 / 276

Keysight N9923-90001 User’s Guide 149

Pulse Measurements Mode – Option 330
Pulse Measurement Settings

—

Frequency

Sets the center frequency of the carrier on which pulse

modulation resides. This is used to set amplitude correction of the

USB Power Sensor.

How to set Time

Specify the time over which data will be acquired by the USB Power Sensor.
When Trace Graph is selected,

Tr 1

is annotated with these values. Time can

be specified using either of the following pairs of values:

—

Center 1

and

Time/div 1

Specify the center time and time per division.

—

Start Time

and

Time Length

Specify the start time and length of

acquisition.

— A positive start time indicates a delay after the sensor detects a pulse

signal.

— A negative start time displays data that is acquired BEFORE the sensor

detects a pulse signal (or T-zero).

— Follow each by entering a value using the numeric keypad, the

arrows,

or the rotary knob.

— After using the keypad, select a multiplier key. Learn about multiplier

abbreviations in

“Multiplier Abbreviations” on page 34

Zoom Window

When Trace Graph is selected as the measurement, a secondary Zoom Trace
can be used to view a zoomed portion of

Tr 1

. When Zoom Window is ON, blue

vertical posts appear on

Tr 1

to indicate the current start, center, and stop

times of the zoom window. The zoom window can be scaled using the standard
Scale settings.

How to make Zoom Window settings

— Press

Measure

— Then

Trace Graph

— Press

Trace 6

— Then

Zoom Window OFF ON

— Then choose from the following:

—

Opens the zoom window on the bottom half of the FieldFox

screen. The window includes the zoomed trace.

—

OFF

Closes the zoom window.

—

Zoom Center

While monitoring the T within the blue vertical posts on

Tr 1

enter a value for the center time using the numeric keypad, the

arrows, or the rotary knob.

Содержание N9923A





















































































































































































































































































Результаты поиска

Содержание N9923A

Отзывы:

Keysight N9923A, Руководство пользователя, Страница: 149 / 276

Результаты поиска

Содержание N9923A

Отзывы: