Keysight N9927-90001 User’s Guide 121
Calibration for NA, CAT, and VVM Modes
scope of this discussion. Although an OPEN standard is a precision
component, simply leaving
nothing
connected at the end of a cable
can be a reasonable substitute for an OPEN.
— A LOAD standard absorbs almost ALL of the incident signal and very
little signal is reflected back to the source.
— A
THRU
standard is used during some calibration steps to connect PORT 1
to PORT 2 in place of the DUT. A Flush THRU connection can be made
when cables that connect with the DUT can mate with each other. Learn
more in
. Otherwise, any reasonably short
cable can be used as a THRU standard.
Calibration Reference Plane
is the point (or points) at which the DUT and cal
standards are connected during a calibration. This can be at the FieldFox test
port connectors, or at the end of jumper cables or adapters.
CalReady
Every FieldFox contains a factory calibration that was performed at the port 1
and port 2 connectors, with -15 dBm input power, over the entire frequency
range of the FieldFox using a number of data points that allows reasonable
interpolation over the FieldFox frequency range.
This calibration, known as CalReady, allows you to immediately make
measurements of a DUT that is connected directly at the test ports (PORT 1
and/or PORT 2). CalReady corrects measurements when the FieldFox is turned
ON and when a measurement is created with no other correction in place.
When measuring a DUT using a jumper cable or adapter - NOT a direct
connection to a test port connector – then a QuickCal or Mechanical Cal is
recommended. CalReady can also be used to check the integrity of the jumper
cable that is attached to the test ports.
CalRdy
is shown when a measurement is corrected using CalReady.
You can change the properties of the CalReady calibration. Learn more in
.
Learn how to see when your factory CalReady calibration was performed in
“System Information” on page 501
.
How to Perform a Calibration
In CAT, NA, or VVM Mode, press
Cal 5
.
Press
Esc
at any time to end the calibration process.
When performing a calibration that contains a large number of points
(5000 to 10,001 points) be aware that the calibration progress bar may not
move for 2 or 3 minutes during the calibration process.
Содержание N9913A
