Keysight N5241BU-205 Скачать руководство пользователя страница 51

Страница: 51 / 60

Installation Note N5242-90125 51

Description of the Upgrade
Installation Procedure for the Upgrade

Operator’s Check

Perform the Operator’s Check to check the basic functionality of the analyzer.

For instructions, click the Chapter 3 bookmark “Tests and Adjustments” in the
PDF Service Guide

If you experience difficulty with the basic functioning of the analyzer, contact

Keysight. Refer to

“Contacting Keysight” on page 4

Calibration

Although the analyzer functions, its performance relative to its specifications

has not been verified. It is recommended that a full instrument calibration be

performed using the analyzer’s internal performance test software. To view

information on the performance test software, click the Chapter 3 bookmark
“Tests and Adjustments” in the PDF Service Guide

Step 35. Prepare the PNA for the User

If necessary, reinstall front jumper cables.

Install the cable guards, pushing them over the front jumper cables until

the cushioning material touches the front panel of the PNA.

Install the dust caps on the test ports.

Clean the analyzer, as needed, using a damp cloth.

Содержание N5241BU-205





























































Результаты поиска

Содержание N5241BU-205

Отзывы:

Похожие инструкции для N5241BU-205

Бренды по названию

Популярные бренды

Keysight N5241BU-205, Установочная инструкция

Результаты поиска

Содержание N5241BU-205

Отзывы:

Похожие инструкции для N5241BU-205

Бренды по названию

Популярные бренды