Keysight N4431D Скачать руководство пользователя страница 52

Страница: 52 / 142

3-2 Electronic Calibration Modules Reference Guide

Operating ECal Module
Setting Up a Calibration

Table 3-2

N443xD and N469xD Status LED Operation

Status LED Color

Description

Off

— ECal is not connected to an

instrument or is malfunctioning.

— See also, Figure

“ECal

Troubleshooting” on page 3-14

Orange

— ECal is warming up.

— ECal connected and functioning, but

is not communicating with the driver

software.

— See also, Figure

“ECal

Troubleshooting” on page 3-14

Steady Green

— ECal is connected, functioning,

warmed up, and communicating
normally.

Alternating Green/Orange Flashing

— ECal is too cold and unable to

regulate internal temperature to

setpoint.

— Performance may be degraded

beyond specifications.

— See also, Figure

“ECal

Troubleshooting” on page 3-14

Alternating Green/Red Flashing

— ECal is too hot and unable to

regulate internal temperature to

setpoint.

— Performance may be degraded

beyond specifications.

— See also, Figure

“ECal

Troubleshooting” on page 3-14

a. Status LED briefly flashes orange when the ECal is first connected to an instrument while the

driver software loads.

Содержание N4431D















































































































































Результаты поиска

Содержание N4431D

Отзывы:

Бренды по названию

Популярные бренды

Keysight N4431D, Справочное руководство

Результаты поиска

Содержание N4431D

Отзывы:

Бренды по названию

Популярные бренды