Keysight MIPI M-PHY Скачать руководство пользователя страница 60

Страница: 60 / 76

Keysight MIPI M-PHY Frame Generator User Guide

Using the Software

Using UniPro Scripts

Setting Up the UniPro Test Mode

Select

UniPro Script Generator

(instead of Script Editor) in the Signal

window if you want to operate in UniPro test mode. See

Figure 25

. UniPro

Scripts have to be generated to replace the default scripts.

Figure 25

Pattern Tab - UniPro Script Generator window for Rx test mode

Parameters in the UniPro Script Generator Window

Sequence

•

Generic Sequence

: The default Generic Sequence should be kept as

“M-PHY_UniPro_BasicBlocks.seq”. This sequence can be edited and

the changes will propagate to all the generated sequences. This

sequence is a template, it cannot be used directly.

•

Output Sequence

: Either set the path for the output sequence or keep

the default one.

•

Generate Patterns

: Click this button to generate the patterns once all

the parameters have been set.

Содержание MIPI M-PHY













































































Результаты поиска

Содержание MIPI M-PHY

Отзывы:

Похожие инструкции для MIPI M-PHY

Бренды по названию

Популярные бренды

Keysight MIPI M-PHY, Руководство пользователя

Результаты поиска

Содержание MIPI M-PHY

Отзывы:

Похожие инструкции для MIPI M-PHY

Бренды по названию

Популярные бренды