Keysight MIPI M-PHY Скачать руководство пользователя страница 11

Страница: 11 / 76

Keysight MIPI M-PHY Frame Generator User Guide

Test Instrument Setup

For system configurations with the M8040A, either a Keysight

M8045A-803 matched coupler pair or a 3dB attenuator should be

connected to the M8057 remote head output of the M8045 module. We

recommend using a 3dB attenuator with a minimum frequency range of

26.5GHz, 2 pieces for each data lane.

This configuration supports the Loopback and UniPro operating modes.

The Keysight M8046A analyzer module can be used to do loopback testing

with continuous patterns. However, it cannot be used to test bursts.

With the M8040A it is also possible to test two receiver channels of the

DUT simultaneously.

J-BERT BIT-3000 DSGA MIPI

M-PHY Generator

To use this setup, select “M8040A” as the “Instrument” in the Connection

window of the software and change “Low speed analyzer (DSGA)” to ON.

For more details, see

Connecting to the Instruments

on page 25.

This system configuration (

Figure 2

) is recommended for the UniPro test

mode. In this case the DSGA is used to trigger the reset of the DUT and to

receive the frame and error counters, while the M8040A is used for the

DUT configuration and to generate the test pattern.

Figure 2

MIPI

M-PHY Frame Generator hardware setup for J-BERT

BIT-3000 DSGA

Содержание MIPI M-PHY













































































Результаты поиска

Содержание MIPI M-PHY

Отзывы:

Похожие инструкции для MIPI M-PHY

Бренды по названию

Популярные бренды

Keysight MIPI M-PHY, Руководство пользователя

Результаты поиска

Содержание MIPI M-PHY

Отзывы:

Похожие инструкции для MIPI M-PHY

Бренды по названию

Популярные бренды