Keysight ixia BreakingPoint 20 Скачать руководство пользователя страница 14

Страница: 14 / 66

HAPTER

Getting Started

Note:

Ensure to review the BreakingPoint Release Notes for the latest installation information

as well as information on new features and resolved issues.

Note:

You can also reference the BreakingPoint User Guide for the most current information on

performing the tasks described in this topic.

This section covers the following:

Getting Started Overview

Task 1: Installing the BreakingPoint Device

Task 2: Configuring the BreakingPoint Device

Task 3: Establishing a BreakingPoint Session

Task 4: Accessing the BreakingPoint Control Center

Task 5: Creating a User Account

Task 6: Setting the Time and Date

Task 7: Creating a Device Under Test Profile

Task 8: Creating a Network Neighborhood

Task 9: Making Port Reservations

Task 10: Creating a Test

Getting Started Overview

This section provides an overview of the tasks that you must complete to install and configure the
BreakingPoint device, as well as explain how to set up your test environment within the BreakingPoint
Control Center.

The following table lists the Getting Started tasks:

Task

Description

Task 1

Installing the BreakingPoint Device.

Task 2

Configuring the BreakingPoint Device.

Task 3

Establishing a BreakingPoint Session.

Task 4

Accessing the BreakingPoint Control Center.

– 9 –

Содержание ixia BreakingPoint 20



































































Результаты поиска

Содержание ixia BreakingPoint 20

Отзывы:

Похожие инструкции для ixia BreakingPoint 20

Бренды по названию

Популярные бренды

Keysight ixia BreakingPoint 20, Руководство по установке

Результаты поиска

Содержание ixia BreakingPoint 20

Отзывы:

Похожие инструкции для ixia BreakingPoint 20

Бренды по названию

Популярные бренды