Keysight InfiniiVision M9241A Скачать руководство пользователя страница 45

Страница: 45 / 72

Keysight M9241/42/43A PXIe Oscilloscopes and M9240A AutoProbe Power Module

Startup Guide

8 Coordinating Multiple PXIe

Oscilloscope Modules

Step 1: (Optional) Update the Calibration Factors / 46
Step 2: Set Up the Slave Modules / 49
Step 3: Set Up the Master Module / 50
Step 4: (When Necessary) Connect Chassis Bus Segments / 51
Step 5: (Recommended) Phase-Lock Oscilloscope Sampling Clocks / 54
Step 6: (Optional) Turn On Sync Mode / 55
Step 7: Make Coordinated Acquisitions / 60

You can synchronize acquisitions between multiple M924xA oscilloscope modules

by using the PXI Trigger Menu to set up coordinated arming and triggering.

Among all the oscilloscope modules to be synchronized, one module must be the

master and all other modules must be slaves. The

PXI Trigger Mode

softkey makes

the master or slave selection for a module (or turns off PXI triggering for the

module, making it a standalone module).

The Trigger Menu on the master oscilloscope module is used to define the trigger

condition. The master module outputs its trigger signal to one of the chassis

PXI_TRIG lines (0-7). All slave modules receive the trigger signal over the same

PXI_TRIG line, and their Trigger Menus simply show that they are PXI slaves.

There is a separate "armed" signal from each slave module so that the master can

wait until each slave is ready before triggering. The remaining PXI_TRIG lines can

be used for the arm lines from the slave modules. With arming control, there can

be up to seven slave modules. (With software arming in remote programs, there

can be more than eight modules in a multiple-module system.)

Arming control is not required; however, if it is not used, a slave module may miss

trigger events from the master module (because the master module may send

triggers when the slave module is not armed).

This chapter assumes you are using the Keysight InfiniiVision M924xA Soft Front

Panel (SFP). If you have not already opened the SFP, see

"Open the M924xA

Oscilloscope Soft Front Panel (SFP)"

on page 29.

Содержание InfiniiVision M9241A









































































Результаты поиска

Содержание InfiniiVision M9241A

Отзывы:

Похожие инструкции для InfiniiVision M9241A

Бренды по названию

Популярные бренды

Keysight InfiniiVision M9241A, Руководство для стартапов

Результаты поиска

Содержание InfiniiVision M9241A

Отзывы:

Похожие инструкции для InfiniiVision M9241A

Бренды по названию

Популярные бренды