manualshive.com logo in svg

Keysight E8663D, Руководство пользователя

Keysight E8663D - мощный и точный генератор сигналов, обеспечивающий высокую стабильность и надежность. Для удобства использования, вы можете скачать бесплатное руководство пользователя с нашего веб-сайта. Наслаждайтесь всеми функциями устройства, загрузив его руководство с manualshive.com.

Поделиться
Скачать
background image

Keysight E8357D/67D & E8663D PSG User’s Guide                                                                                                 317

Troubleshooting

RF Output Power Problems

reverse power can cause amplitude modulation of the signal generator’s RF 

output. The rate of the undesired AM equals the difference in frequency 

between the spectrum analyzer’s LO feedthrough and the RF carrier of the 

signal generator.
Reverse power problems can be solved by using one of two unleveled 

operating modes: ALC off or power search.

Setting ALC Off Mode

ALC off mode deactivates the automatic leveling circuitry prior to the signal 

generator’s RF output. In this mode, a power meter is required to measure the 

output of the signal generator and assist in achieving the required output 

power at the point of detection. 
Use the following steps to set the signal generator to the ALC off mode:

1.

Preset the signal generator: press 

Preset

.

2.

Set the desired frequency: press 

Frequency

 and enter the desired 

frequency.

3.

Set the desired amplitude: press 

Amplitude

 and enter the desired 

amplitude.

4.

Turn the RF on: set 

RF On/Off

 to On

5.

Turn the signal generator’s automatic leveling control (ALC) off: press 

Amplitude

 > 

ALC Off On

 to Off.

6.

Monitor the RF output amplitude as measured by the power meter.

Press 

Amplitude

 and adjust the signal generator’s RF output amplitude 

until the desired power is measured by the power meter.

Poor Pulse Performance

For pulse widths <1 microsecond, you may need to do a power search to 

optimize the pulse performance of the instrument. Refer to 

“Setting Power 

Search Mode” on page 317

.

Setting Power Search Mode

Power search mode executes a power search routine that temporarily closes 

the ALC, calibrates the power of the current RF output, and then opens the 

ALC circuitry. See the Keysight PSG Signal Generators Key Reference for more 

information on the Power Search function. 

CAUTION

There are two “RF During Power Search” settings available for the power 

search, Minimum and Normal. The Minimum softkey sets the internal 

attenuator to its maximum setting during power search to protect the power 

sensitive circuits. When the power search has completed the attenuator is 

returned to the last attenuator setting before the power search was executed. 

The Normal softkey executes the power search without this added attenuator 

protection.

Содержание E8663D







































































































































































































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для E8663D

Oster OPB9000 Instruction/Recipe Booklet preview
OPB9000
Бренд: Oster Страницы: 12
George Foreman MIX & GO PRO Instructions & Warranty preview
MIX & GO PRO
Бренд: George Foreman Страницы: 22
Amplitec C15F-5B User Manual preview
C15F-5B
Бренд: Amplitec Страницы: 13
opticis AVFX-100-TR User Manual preview
AVFX-100-TR
Бренд: opticis Страницы: 7
Waring BB145 Series Instruction Manual preview
BB145 Series
Бренд: Waring Страницы: 17
weBoost Drive Reach Fleet Installation Manual preview
Drive Reach Fleet
Бренд: weBoost Страницы: 16
Gefen GTB-UHD-HBT User Manual preview
GTB-UHD-HBT
Бренд: Gefen Страницы: 46
T-Fal Mini Instruction Manual preview
Mini
Бренд: T-Fal Страницы: 33
Black & Decker BDXPA0051 Instruction Manual preview
BDXPA0051
Бренд: Black & Decker Страницы: 10
KitchenAid KSB465ER0 Parts List preview
KSB465ER0
Бренд: KitchenAid Страницы: 3
KitchenAid KHBC10 Series Manual preview
KHBC10 Series
Бренд: KitchenAid Страницы: 8
KitchenAid KSB465 Instructions Manual preview
KSB465
Бренд: KitchenAid Страницы: 44
KitchenAid KHB2351 Manual preview
KHB2351
Бренд: KitchenAid Страницы: 40
KitchenAid KHB2561 Instructions And Recipes Manual preview
KHB2561
Бренд: KitchenAid Страницы: 64
KitchenAid KHBC208 Instructions Manual preview
KHBC208
Бренд: KitchenAid Страницы: 44
KitchenAid KSB354 Instructions Manual preview
KSB354
Бренд: KitchenAid Страницы: 44
KitchenAid KSB560AQ - Martha Stewart - Collection Blender Parts List preview
KSB560AQ - Martha Stewart - Collection Blender
Бренд: KitchenAid Страницы: 3
KitchenAid KSB540OB Manual preview
KSB540OB
Бренд: KitchenAid Страницы: 7

Бренды по названию

Популярные бренды

Загрузить еще бренды