Keysight E8663D Скачать руководство пользователя страница 224

Страница: 224 / 358

210 Keysight E8357D/67D & E8663D PSG User’s Guide

Custom Arb Waveform Generator
Configuring Hardware

Configuring Hardware

To Set a Delayed, Positive Polarity, External Single Trigger

Using this procedure, you learn how to utilize an external function generator to

apply a delayed single–trigger to a custom multicarrier waveform.

Connect an Keysight 33120A function generator or equivalent to the signal

generator PATT TRIGGER IN port, as shown in

Figure 6-1

Figure 6-1

On the signal generator, press

Preset

Press

Mode

Custom

Arb Waveform Generator

Press

Multicarrier Off On

until On is highlighted.

Press

Trigger

Single

Press

Trigger

Trigger Setup

Trigger Source

Ext

Press

Ext Polarity Neg Pos

until Pos is highlighted.

Press

Ext Delay Off On

until On is highlighted.

Press

Ext Delay Time

100

msec

The Custom Arb Waveform Generator has been configured to play a single

multicarrier waveform 100 milliseconds after it detects a change in TTL

state from low to high at the PATT TRIG IN rear panel connector.

10.

Set the function generator waveform to a 0.1 Hz square wave at an output

level of 0 to 5V.

11.

On the signal generator, press

Mode

Custom

Arb Waveform

Generator

Digital Modulation Off On

until On is highlighted.

This generates a waveform with the custom multicarrier state and the

display changes to

Dig Mod Setup: Multicarrier

During waveform generation, the

DIGMOD

and

I/Q

annunciators activate

and the new custom multicarrier state is stored in volatile ARB memory.

The waveform should be modulating the RF carrier.

12.

Press

RF On/Off

Содержание E8663D







































































































































































































































































































































































Результаты поиска

Содержание E8663D

Отзывы:

Похожие инструкции для E8663D

Бренды по названию

Популярные бренды

Keysight E8663D, Руководство пользователя

Результаты поиска

Содержание E8663D

Отзывы:

Похожие инструкции для E8663D

Бренды по названию

Популярные бренды