Keysight E8663D Скачать руководство пользователя страница 107

Страница: 107 / 358

Keysight E8357D/67D & E8663D PSG User’s Guide 93

Basic Digital Operation
Arbitrary (ARB) Waveform File Headers

Figure 3-1

Custom Digital Modulation First–Level Softkey Menu

At this point, a default file header has been created, with default

(unspecified) settings that do not reflect the current signal generator

settings for the active modulation. To save the settings for the active

modulation, you must modify the default settings before you save the

header information with the waveform file (see

“Modifying Header

Information in a Modulation Format” on page 93

NOTE

Each time an ARB modulation format is turned on, a new temporary

waveform file (AUTOGEN_WAVEFORM) and file header are generated,

overwriting the previous temporary file and file header. Because all ARB

formats use the same file name, this happens even if the previous

AUTOGEN_WAVEFORM file was created by a different ARB modulation

format.

Modifying Header Information in a Modulation Format

This procedure builds on the previous procedure, explaining the different areas

of a file header, and showing how to access, modify, and save changes to the

information.
In a modulation format, you can access a file header only while the modulation

format is active (on). This procedure uses the Custom digital modulation

format. All ARB modulation formats and the dual ARB player access the file

header the same way, except that in some modulation formats, you may have

to go to page two of the first–level softkey menu.

From the first–level softkey menu (shown in

Figure 3-1 on page 93

), open

the Header Utilities menu:

Press

ARB Setup

Header Utilities

Figure 3-2

shows the default header for the Custom digital modulation

waveform. The

Saved Header Settings

column, shows that the signal

generator settings for the active format are

Unspecified

, which means

that no settings have been saved to the file header.

First–Level Softkey Menu

(Some ARB formats have a

second page)

Содержание E8663D







































































































































































































































































































































































Результаты поиска

Содержание E8663D

Отзывы:

Keysight E8663D, Руководство пользователя, Страница: 107 / 358

Результаты поиска

Содержание E8663D

Отзывы: