Keysight E6650A EXF Скачать руководство пользователя страница 169 | Manualshive

Страница: 169 / 657

background image

5 System Functions

System

The utility may also be called if, during operation of the analyzer, you attempt to load more applications
than can fit in memory at once.

Virtual memory usage

There are more applications available for the X-Series than can fit into memory at any one time, so the
Configure Applications utility includes a memory tracker that serves two purposes:

1. It will not let you preload more applications than will fit into memory at once.

2. You can determine how many of your favorite applications can reside in memory at one time.

The utility provides a graphical representation of the amount of memory (note that the memory in question
here is Virtual memory and is a limitation imposed by the operating system, not by the amount of physical
memory you have in your analyzer). You select applications to preload by checking the boxes on the left.
Checked applications preload at startup. The colored fuel bar indicates the total memory required when
all the checked applications are loaded (either preloaded or selected during runtime).

Here is what the fuel bar colors mean:

RED: the applications you have selected cannot all fit into the analyzer’s memory. You must deselect
applications until the fuel bar turns yellow.

YELLOW: the applications you have selected can all fit into the analyzer’s memory, but there is less than
10% of the memory left, probably not enough to load any other applications, either via preload or by
selecting a Mode while the analyzer is running..

GREEN: The indicator is green when <90% of the memory limit is consumed. This means the applications
you have selected can all fit into the analyzer’s memory with room to spare. You will likely be able to load
one or more other applications without running out of memory.

Select All

Marks all applications in the selection list. This allows you to enable all applications licensed on the
instrument for pre-loading, or is a convenience for selecting all applications in one operation and then
letting you deselect individual applications.

Key Path

System, Power On, Configure Applications

Initial S/W Revision

A.02.00

Deselect All

Clears the marks from all applications in the selection list, except the Power On application. The Power On
application cannot be eliminated from the pre-load list.

Key Path

System, Power On, Configure Applications

Initial S/W Revision

A.02.00

Sequence Analyzer User's & Programmer's Reference

169

«
...
167
168
169
170
171
...
»

Содержание E6650A EXF


















































































































































































































































































































































































































































































































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для E6650A EXF

Бренд: Labnet Страницы: 5

Бренд: Major Страницы: 52

Бренд: H&S Страницы: 42

Бренд: MacDon Страницы: 46

Бренд: MacDon Страницы: 82

Бренд: Mac Medical Страницы: 2

Бренд: MACDEV Страницы: 8

Mentor Touch ET750

Бренд: MAC TOOLS Страницы: 24

Бренд: MA lighting Страницы: 10

Бренд: Yamaha Страницы: 139

Бренд: Yamaha Страницы: 19

Бренд: Yamaha Страницы: 32

Бренд: VaBroom Страницы: 4

Wallach UltraFreeze

Бренд: Cooper Surgical Страницы: 4

500 FleetBroadband

Бренд: Sailor Страницы: 20

TetraGraph Philips Interface

Бренд: SENZIME Страницы: 20

Бренд: AS MOTOR Страницы: 36

Бренд: HOMCOM Страницы: 11

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды