Keysight DSOX3012T Скачать руководство пользователя страница 43 | Manualshive

Страница: 43 / 530

background image

Getting Started

1

Keysight InfiniiVision 3000T X-Series Oscilloscopes User's Guide

43

17.

Analog channel

inputs

Attach oscilloscope probes or BNC cables to these BNC connectors.
With the InfiniiVision 3000T X-Series oscilloscopes, you can set the input impedance of the
analog channels to either 50

Ω

or 1 M

Ω

. See

“To specify channel input impedance"

page 82.
The InfiniiVision 3000T X-Series oscilloscopes also provide the AutoProbe interface. The

AutoProbe interface uses a series of contacts directly below the channel's BNC connector to

transfer information between the oscilloscope and the probe. When you connect a compatible

probe to the oscilloscope, the AutoProbe interface determines the type of probe and sets the

oscilloscope's parameters (units, offset, attenuation, coupling, and impedance) accordingly.

18.

Demo 2, Ground, and

Demo 1 terminals

•

Demo 2 terminal — After a

[Default Setup]

, this terminal outputs the Probe Comp signal

which helps you match a probe's input capacitance to the oscilloscope channel to which it

is connected. See

“Compensate Passive Probes"

on page 36. With certain licensed

features, the oscilloscope can also output demo or training signals on this terminal.

•

Ground terminal — Use the ground terminal for oscilloscope probes connected to the Demo

1 or Demo 2 terminals.

•

Demo 1 terminal — The oscilloscope can output training signals on this and the Demo 2

terminal. See:

[Help] > Training Signals > Training Signals

.

19.

USB Host port

This port is for connecting a USB mass storage device, printer, mouse, or keyboard to the

oscilloscope.
Connect a USB compliant mass storage device (flash drive, disk drive, etc.) to save or recall

oscilloscope setup files and reference waveforms or to save data and screen images. See

, “Save/Email/Recall (Setups, Screens, Data),” starting on page 321.

To print, connect a USB compliant printer. For more information about printing see

, “Print (Screens),” starting on page 335.

You can also use the USB port to update the oscilloscope's system software when updates are

available.
You do not need to take special precautions before removing the USB mass storage device

from the oscilloscope (you do not need to "eject" it). Simply unplug the USB mass storage

device from the oscilloscope when the file operation is complete.

CAUTION:

Do not connect a host computer to the oscilloscope's USB host port.

Use the

device port. A host computer sees the oscilloscope as a device, so connect the host computer

to the oscilloscope's device port (on the rear panel). See

“I/O Interface Settings"

page 341.
There is a second USB host port on the back panel.

20.

Digital channel

inputs

Connect the digital probe cable to this connector (MSO models only). See

Channels,” starting on page 131.

«
...
41
42
43
44
45
...
»

Содержание DSOX3012T



















































































































































































































































































































































































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для DSOX3012T

Бренд: Gardena Страницы: 13

Бренд: JB Systems Страницы: 7

Бренд: 3B SCIENTIFIC PHYSICS Страницы: 36

Бренд: 3A HEALTH CARE Страницы: 16

Short/cut 2000 Audio Editor

Бренд: 360 Systems Страницы: 4

Бренд: Zenbooth Страницы: 60

Бренд: Raven Страницы: 12

Бренд: Zero 88 Страницы: 20

Бренд: Kapriol Страницы: 32

Бренд: Cabletron Systems Страницы: 33

Бренд: i-CAT Страницы: 32

Бренд: NatureZap Страницы: 2

ProFire Lightbridge

Бренд: M-Audio Страницы: 8

Бренд: M-Audio Страницы: 36

Бренд: Major tech Страницы: 12

Бренд: Petromax Страницы: 16

Бренд: SereneLife Страницы: 4

Бренд: SDE Lighting Страницы: 7

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды