Keysight DSOX3012T Скачать руководство пользователя страница 392

Страница: 392 / 530

392

Keysight InfiniiVision 3000T X-Series Oscilloscopes User's Guide

Reference

Product Markings and Regulatory Information

These symbols are used on the 3000T X-Series oscilloscopes.

websockify

Keysight. Keysight will charge for the cost of physically performing the

source distribution.

Lesser or Library

General Public License

version 3.0 (LGPLv3)

zlib

zlib license

These licenses are located on the Keysight InfiniiVision oscilloscopes manuals CD-ROM.

Table 7

Third Party Software (continued)

Software

Description and Copyright

License

Symbol

Description

Caution, risk of electric shock

Caution, refer to accompanying documentation

This symbol indicates separate collection for electrical and electronic

equipment mandated under EU law as of August 13, 2005. All electric and

electronic equipment are required to be separated from normal waste for

disposal (Reference WEEE Directive 2002/96/EC).

Indicates the time period during which no hazardous or toxic substance

elements are expected to leak or deteriorate during normal use. Forty

years is the expected useful life of the product.

The RCM mark is a registered trademark of the Australian

Communications and Media Authority.

Содержание DSOX3012T



















































































































































































































































































































































































































































































































































Результаты поиска

Содержание DSOX3012T

Отзывы:

Похожие инструкции для DSOX3012T

Бренды по названию

Популярные бренды

Keysight DSOX3012T, Руководство пользователя

Результаты поиска

Содержание DSOX3012T

Отзывы:

Похожие инструкции для DSOX3012T

Бренды по названию

Популярные бренды