Keysight DSOX3012T Скачать руководство пользователя страница 317

Страница: 317 / 530

Waveform Generator

Keysight InfiniiVision 3000T X-Series Oscilloscopes User's Guide

317

When the modulating signal is at its maximum amplitude, the output frequency

is the carrier signal frequency plus the deviation amount, and when the

modulating signal is at its minimum amplitude, the output frequency is the

carrier signal frequency minus the deviation amount.

The frequency deviation cannot be greater than the original carrier signal

frequency.

Also, the sum of the original carrier signal frequency and the frequency

deviation must be less than or equal to the maximum frequency for the selected

waveform generator function plus 100 kHz.

The following screen shows an FM modulation of a 100 kHz sine wave carrier

signal.

To set up Frequency-Shift Keying Modulation (FSK)

In the Waveform Generator Modulation Menu (under

[Wave Gen] > Settings >

Modulation

Press the

Type

softkey and turn the Entry knob to select

Frequency-Shift Keying

Modulation (FSK)

Содержание DSOX3012T



















































































































































































































































































































































































































































































































































Результаты поиска

Содержание DSOX3012T

Отзывы:

Похожие инструкции для DSOX3012T

Бренды по названию

Популярные бренды

Keysight DSOX3012T, Руководство пользователя

Результаты поиска

Содержание DSOX3012T

Отзывы:

Похожие инструкции для DSOX3012T

Бренды по названию

Популярные бренды