Keysight DSOX3012T Скачать руководство пользователя страница 272

Страница: 272 / 530

272

Keysight InfiniiVision 3000T X-Series Oscilloscopes User's Guide

Measurements

Measurement Window

You can choose whether measurements are made in the Main window portion of

the display, the Zoom window portion of the display (when the zoomed time base

is displayed), or gated by the X1 and X2 cursors.

Press the

[Meas]

key.

In the Measurement Menu, press the

Meas Window

softkey; then, turn the Entry

knob to select from:

•

Auto Select

— When the zoomed time base is displayed, the measurement is

attempted in the lower, Zoom window; if it cannot be made there, or if the

zoomed time base is not displayed, the Main window is used.

•

Main

— The measurement window is the Main window.

•

Zoom

— The measurement window is the lower, Zoom window.

•

Gated by Cursors

— The measurement window is between the X1 and X2

cursors. When the zoomed time base is displayed, the X1 and X2 cursors in

the Zoom window portion of the display are used.

Measurement Statistics

To display measurement statistics:

Press the

[Meas]

key to enter the Measurement Menu. By default frequency and

peak-to-peak voltage are measured on channel 1.

Select the measurements you desire for the channels you are using (see

“Measurements Summary"

on page 246).

From the Measurement Menu, press the

Statistics

softkey to enter the Statistics

Menu.

Press the

Display On

softkey to enable the measurement statistics display.

Содержание DSOX3012T



















































































































































































































































































































































































































































































































































Результаты поиска

Содержание DSOX3012T

Отзывы:

Похожие инструкции для DSOX3012T

Бренды по названию

Популярные бренды

Keysight DSOX3012T, Руководство пользователя

Результаты поиска

Содержание DSOX3012T

Отзывы:

Похожие инструкции для DSOX3012T

Бренды по названию

Популярные бренды