Keysight Technologies U3022AH10 Скачать руководство пользователя страница 42

Страница: 42 / 92

U3022AH10

Controlling the System with N5242A/B

How to Access Interface Control Settings

This section describes how to configure and operate the test set with the PNA.



1. To access the Interface Control mode, select

Trace/Chan > Channel > Hard ware Setup > Interface Control -OR-

(Instrument > Setup > Internal Hardware > Interface Control...)

the drop-down menu, and select Enable Interface Control.

The PNA Series Network Analyzer comes with the Interface Control application.

Please review this application before connecting the test set to the PNA.

Information regarding this application can be found in the PNA Help menu,

Interface Control. The application is shown in

Figure 3

below.

Figure 3

Interface Control

Application

U3022AH10 User's and Service Guide

Содержание U3022AH10





























































































Результаты поиска

Содержание U3022AH10

Отзывы:

Похожие инструкции для U3022AH10

Бренды по названию

Популярные бренды

Keysight Technologies U3022AH10, Руководство пользователя и сервисное руководство

Результаты поиска

Содержание U3022AH10

Отзывы:

Похожие инструкции для U3022AH10

Бренды по названию

Популярные бренды