Keysight Technologies U3022AH10 Скачать руководство пользователя страница 23

Страница: 23 / 92

U3022AH10

System Configurations

4. Install the two rear locking feet onto the U3022AH10. Looking at the front panel, the

N5242-20138 (for Std) or N5242-20206 (for Opt 129) is the right foot and the

N5242-20139 (for Std) or N5242-20207 (for Opt 129) is the left foot. Two

screws (0515-2317) are included with

these rear feet

Figure

Install Locking Feet on U3022AH10

(STD shown)

5. Place the network analyzer on top of the Test Set and ensure that the front frame of the network

analyzer is positioned slightly forward of the

Lock-Links (shown in

Figure 10

below)

that are

attached to the Test Set. Slide the

network analyzer back so the locks engage the front frame

of the analyzer.

Figure

Locking the Analyzer

to the Test Set

Test Set
Front Frame

Network Analyzer
Front Frame

Slide the network Analyzer
back to engage the lock link
in the back of the network
analyzer's front frame

Lock Link

screw

The

Lock-Links are pre-installed on the Test Set at the factory.

U3022AH10 User's and Service Guide

Содержание U3022AH10





























































































Результаты поиска

Содержание U3022AH10

Отзывы:

Похожие инструкции для U3022AH10

Бренды по названию

Популярные бренды

Keysight Technologies U3022AH10, Руководство пользователя и сервисное руководство

Результаты поиска

Содержание U3022AH10

Отзывы:

Похожие инструкции для U3022AH10

Бренды по названию

Популярные бренды