Keysight Technologies U2741A Скачать руководство пользователя

Страница: 6 / 63

Keysight U2741A User’s Guide

Regulatory Markings

The CE mark is a registered trademark

of the European Community. This CE

mark shows that the product complies

with all the relevant European Legal

Directives.

The RCM mark is a registered

trademark of the Spectrum

Management Agency of Australia.

This signifies compliance with the

Australia EMC Framework regulations

under the terms of the Radio

Communication Act of 1992.

ICES/NMB-001 indicates that this ISM

device complies with the

Canadian ICES-001.

Cet appareil ISM est conforme a la

norme NMB-001 du Canada.

This instrument complies with the

WEEE Directive (2002/96/EC) marking

requirement. This affixed product label

indicates that you must not discard

this electrical or electronic product in

domestic household waste.

The CSA mark is a registered

trademark of the Canadian

Standards Association.

Содержание U2741A
































































Результаты поиска

Содержание U2741A

Отзывы:

Похожие инструкции для U2741A

Бренды по названию

Популярные бренды

Keysight Technologies U2741A, Руководство пользователя

Результаты поиска

Содержание U2741A

Отзывы:

Похожие инструкции для U2741A

Бренды по названию

Популярные бренды