Keysight Technologies N5511A Скачать руководство пользователя страница 337

Страница: 337 / 369

N5511A Phase Noise Test System User’s Guide 337

Reference Graphs and Tables
Phase Lock Loop Bandwidth vs. Peak Tuning Range

Phase Lock Loop Bandwidth vs. Peak Tuning Range

The graph in

Figure 16-10

illustrates the closed Phase Lock Loop Bandwidth

(PLL BW) chosen by the test system as a function of the Peak Tuning Range of

the source. Knowing the approximate closed PLL BW allows you to verify that

there is sufficient bandwidth on the tuning port and that sufficient source

isolation is present to prevent injection locking.

Figure 16-10

PLL BW vs. peak tuning range

Содержание N5511A


















































































































































































































































































































































































Результаты поиска

Содержание N5511A

Отзывы:

Похожие инструкции для N5511A

Бренды по названию

Популярные бренды

Keysight Technologies N5511A, Руководство пользователя

Результаты поиска

Содержание N5511A

Отзывы:

Похожие инструкции для N5511A

Бренды по названию

Популярные бренды