manualshive.com logo in svg

Keysight Technologies N5511A, Руководство пользователя

Поделиться
Скачать
Keysight Technologies N5511A Скачать руководство пользователя страница 334

 334                                                                                              N5511A Phase Noise Test System User’s Guide

Reference Graphs and Tables
Voltage Controlled Source Tuning Requirements

Voltage Controlled Source Tuning Requirements

Peak Tuning Range (PTR) » Tune Range of VCO x VCO Tune Constant.

Min. PTR = 0.1 Hz
Max. PTR = Up to 200 MHz, depending on analyzer and phase detector LPF.
Drift Tracking Range = Allowable Drift During Measurement 

The tuning range that the software actually uses to maintain quadrature is 

limited to a fraction of the peak tuning range (PTR) to ensure that the tuning 

slope is well behaved and the VCO Tune Constant remains accurate. After 

phase lock is established, the test system monitors the tuning voltage required 

to maintain lock. If the tuning voltage exceeds 5% of the PTR during the 

measurement, the test system again informs the user and requests the 

oscillator be retuned or the problem be otherwise corrected before proceeding 

with the measurement. These limits have been found to guarantee good 

results. Refer to 

Figure 16-7

.

Figure 16-7 

Tuning voltage required for phase lock

Содержание N5511A


















































































































































































































































































































































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды