manualshive.com logo in svg

Keysight Technologies N5511A, Руководство пользователя

Поделиться
Скачать
Keysight Technologies N5511A Скачать руководство пользователя страница 332

 332                                                                                              N5511A Phase Noise Test System User’s Guide

Reference Graphs and Tables
Approximate Sensitivity of Delay Line Discriminator

Approximate Sensitivity of Delay Line Discriminator

The dependence of a frequency discriminator's sensitivity on the offset 

frequency is obvious in the graph in 

Figure 16-5

. By comparing the sensitivity 

specified for the phase detector to the delay line sensitivity, it is apparent the 

delay line sensitivity is “tipped up” by 20 dB/decade beginning at an offset of 

1/2

πτ

. The sensitivity graphs indicate the delay line frequency discriminator 

can be used to measure some types of sources with useful sensitivity. Longer 

delay lines improve sensitivity, but eventually the loss in the delay line will 

exceed the available power of the source and cancel any further improvement. 

Also, longer delay lines limit the maximum offset frequency that can be 

measured.

Figure 16-5 

Delay line discriminator sensitivity

Содержание N5511A


















































































































































































































































































































































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды