manualshive.com logo in svg

Keysight Technologies N5511A, Руководство пользователя

Поделиться
Скачать
Keysight Technologies N5511A Скачать руководство пользователя страница 331

N5511A Phase Noise Test System User’s Guide                                                                                                331

Reference Graphs and Tables
Increase in Measured Noise as Ref Source Approaches DUT Noise

Increase in Measured Noise as Ref Source Approaches DUT Noise

The graph shown in 

Figure 16-4

 demonstrates that as the noise level of the 

reference source approaches the noise level of the DUT, the level measured by 

the software (which is the sum of all sources affecting the test system) is 

increased above the actual noise level of the DUT.

Figure 16-4 

Reference source and DUT noise levels

Содержание N5511A


















































































































































































































































































































































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды