manualshive.com logo in svg

Keysight Technologies N5511A, Руководство пользователя

Поделиться
Скачать
Keysight Technologies N5511A Скачать руководство пользователя страница 328

 328                                                                                              N5511A Phase Noise Test System User’s Guide

Reference Graphs and Tables
Approximate System Noise Floor vs. R Port Signal Level

Approximate System Noise Floor vs. R Port Signal Level

The sensitivity of the phase noise measurement system can be improved by 

increasing the signal power at the R input port (Signal Input) of the phase 

detector in the test set. 

Figure 16-1

 illustrates the approximate noise floor of 

the N5500A test set for a range of R input port signal levels from –15 dBm to 

+15 dBm. These estimates of sensitivity assume the signal level at the L port is 

appropriate for either the microwave or the RF mixer that is used (+7 dBm or 

+15 dBm, respectively). The approximate phase detector calibration constant 

that results from the input signal level at the R port is shown on the right side 

of the graph.

Figure 16-1 

Noise floor for R input port

Содержание N5511A


















































































































































































































































































































































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды