manualshive.com logo in svg

Keysight Technologies N5511A, Руководство пользователя

Поделиться
Скачать
Keysight Technologies N5511A Скачать руководство пользователя страница 252

 252                                                                                              N5511A Phase Noise Test System User’s Guide

FM Discriminator Measurement Examples
FM Discriminator Single Channel Measurement using FM Rate and Deviation 

Calibration

5.

The system can now run the measurement. At the appropriate point, 

re-establish quadrature and continue the measurement.
The segment data will be displayed on the computer screen as the data is 

taken until all segments have been taken over the entire range you 

specified in the Measurement definition’s Type and Range.

When the measurement is complete 

When the measurement is complete, refer to 

Chapter 14, “Evaluating Your 

Measurement Results”

 for help in evaluating your measurement results. (If the 

test system has problems completing the measurement, it will inform you by 

placing a message on the computer display. 

Figure 10-19

 shows a typical absolute measurement using FM discrimination.

Figure 10-19 

Typical phase noise curve using FM Rate and Deviation calibration

Содержание N5511A


















































































































































































































































































































































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды