Keysight Technologies N5221BU-605 Скачать руководство пользователя страница 72

Страница: 72 / 88

72 Installation Note N5222-90114

Installation Procedure for the Upgrade

Step 43. Reinstall Front Panel Assembly

For instructions on reinstalling the front panel assembly, click the Chapter 7

bookmark “Removing and Replacing the Front Panel Assembly” in the PDF
Service Guide

— Be sure to install the two new screws (0515-1946) in the front panel, next to

test ports 3 and 4. Torque these screws to 9 in-lbs.

Step 44. Install the New Lower Front Panel Overlay

To see an image of the front panel overlay (N5222-80036), refer to

Figure 42

on page 71

. New parts are listed in

Table 2 on page 11

1. Remove the protective backing from the new front panel overlay

(N5242-80036).

2. Loosely place the overlay in the recess on the lower front panel.

3. Placing two fingers at the middle, press the overlay firmly onto the frame

while sliding your fingers in opposite directions towards the ends of the

overlay. Repeat on all areas of the overlay.

Step 45. Install the Front Panel Jumper Cables

Install twelve W30 front panel jumper cables (N5222-20091) - use 6 new

jumpers and reuse 6 old jumpers. To see an image of the front panel jumper

cables, click the Chapter 7 bookmark “Removing and Replacing the Front
Panel Assembly” in the PDF Service Guide

1. See

“Downloading the Online PNA Service Guide” on page 8

Содержание N5221BU-605

























































































Результаты поиска

Содержание N5221BU-605

Отзывы:

Похожие инструкции для N5221BU-605

Бренды по названию

Популярные бренды

Keysight Technologies N5221BU-605, Установочная инструкция

Результаты поиска

Содержание N5221BU-605

Отзывы:

Похожие инструкции для N5221BU-605

Бренды по названию

Популярные бренды