Keysight Technologies N5221BU-605 Скачать руководство пользователя страница 54

Страница: 54 / 88

54 Installation Note N5222-90114

Installation Procedure for the Upgrade

Step 36. Install the New Test Set Cables and Install Cable Clamps on

Ferrite Beads

This step contains the following:

—

“Install the Flexible Cables Required for Upgrading to an Option 405 PNA”

on page 55

—

“Install the Semirigid Cables Required for Upgrading to an Option 405

PNA” on page 55

—

“Connect New Port 4 N5240-60098 (x1) and Verify Port 2 N5240-60097

Blue Bias-Tee Combiner Cables and Clamps from the A73 and A74 Bias

Tees “RF-IN” to the A70 LFE Board “Port2” and “Port4” Connectors and

Install Clamps onto the Ferrite Beads” on page 64

—

“Connect New N5240-60098 (x1) Port 3 and Verify N5240-60098 Port 1

Blue Bias-Tee Combiner Cables and Clamps from the A71 and A72 Bias

Tees “RF-IN” to the A70 LFE Board “Port1” and “Port3” Connectors and

Install Clamps onto the Ferrite Beads” on page 65

Follow instructions carefully when making cable connections, especially

wire harness connections. Incorrect connections can destroy components,

resulting in additional customer costs.

Be careful not to damage the center pins of the semi-rigid cables. Some

flexing of the cables may be necessary but do not over-bend them.

To avoid damage when connecting and torquing the bias T combiner

semirigid cables, always use a wrench to hold the bias T combiner

connectors.

Use a 5/16-in torque wrench set to 10 in-lbs on all cable connections

except the front and rear panel bulkhead connectors. Torque these

connections to 21 in-lb.

Cables that are to be reinstalled are designated with “reuse.”

Содержание N5221BU-605

























































































Результаты поиска

Содержание N5221BU-605

Отзывы:

Похожие инструкции для N5221BU-605

Бренды по названию

Популярные бренды

Keysight Technologies N5221BU-605, Установочная инструкция

Результаты поиска

Содержание N5221BU-605

Отзывы:

Похожие инструкции для N5221BU-605

Бренды по названию

Популярные бренды