Keysight Technologies N5221BU-605 Скачать руководство пользователя страница 41

Страница: 41 / 88

Installation Note N5222-90114 41

Installation Procedure for the Upgrade

Step 24. Install the LED Boards and Test Port Coupler Assemblies On

the 4-Port Test Set Front Plate

1. Remove two screws from each LED board and remove the boards from the

2-port test set front plate of the PNA. Keep the screws and LED boards for

reuse later.

2. Remove the bulkhead connectors, nuts and washers from the 2-port front

plate to reuse later.

3. Remove the 2-port test set front plate from the test set deck. Keep the

screws for reuse later, but dispose of the test set front plate.

4. Follow the two instructions shown in

Figure 20

LED Board Assemblies and Test Port Coupler Assemblies Installation

(5087-7813, 5022-1087, and N5221-0007)

Содержание N5221BU-605

























































































Результаты поиска

Содержание N5221BU-605

Отзывы:

Похожие инструкции для N5221BU-605

Бренды по названию

Популярные бренды

Keysight Technologies N5221BU-605, Установочная инструкция

Результаты поиска

Содержание N5221BU-605

Отзывы:

Похожие инструкции для N5221BU-605

Бренды по названию

Популярные бренды