Keysight Technologies N5221A Скачать руководство пользователя

Страница: 95 / 368

Keysight N5221A/22A Service Guide 4-21

Troubleshooting
Rear Panel Troubleshooting

Rear Panel Troubleshooting

Each rear panel connector is associated with a hardware group in the analyzer.

You can use the data at these rear panel connectors to help troubleshoot these

hardware groups in addition to testing the connectors.
The connectors discussed in this section are:

• USB x 4
• Monitor (VGA)
• GPIB (0) CONTROLLER
• GPIB (1) TALKER/LISTENER
• LAN

Checking the USB Ports

To verify proper operation of any rear panel USB port:

— Connect a known good USB device, such as a USB mouse.
— Wait 15 seconds for the analyzer to verify the device connection, and then

check the operation of the USB device.

— If the device performs correctly, the USB port is functioning properly.
— If the device does not perform correctly, remove the non-working USB

device, wait 15 seconds, and then reconnect the device to the rear panel

USB port.

— If the USB device still does not work and has been verified to work

elsewhere, then the A17 CPU board is faulty. Refer to

“Removing and

Replacing the A17 CPU Board Assembly” on page 7-25

Checking the CONTROLLER Port

The network analyzer uses a National Instruments 488.2 GPIB controller and

associated driver software. This software includes a test utility that scans the

GPIB bus and returns the status of all the connected peripherals.
To run the test utility software and check the GPIB status:

Connect a known good peripheral to the analyzer using a

known good

GPIB cable.

Press UTILITY

, then

. A

SICL/GPIB/SCPI

dialog box is displayed.

In the

GPIB

block, click

System Controller

to establish the analyzer as a

controller. Wait for the analyzer to configure, and then click

System

Configure

SICL/GPIB

...

Содержание N5221A

















































































































































































































































































































































































Результаты поиска

Содержание N5221A

Отзывы:

Похожие инструкции для N5221A

Бренды по названию

Популярные бренды

Keysight Technologies N5221A, Руководство по обслуживанию

Результаты поиска

Содержание N5221A

Отзывы:

Похожие инструкции для N5221A

Бренды по названию

Популярные бренды