Keysight Technologies N5221A Скачать руководство пользователя

Страница: 63 / 368

Keysight N5221A/22A Service Guide 3-35

Tests and Adjustments
Performance Tests

Description of the Test:
Trace Noise is a calculation of the standard deviation of a 201 point CW

measurement. In a healthy analyzer, this measurement is only affected by the

sampling error of the analog to digital converters on the SPAM board.
Ports 1 and 2 are tested as a pair using S21 and S12 measurements. Ports 3

and 4 are similarly tested as a pair on 4-port analyzers using S43 and S34

measurements.

The analyzer is Preset.

The analyzer is set up for a 201 point CW transmission measurement for

the port pair to be tested with the specified IF bandwidth (typically 1 kHz).

Both a magnitude and a phase trace are displayed.

A test cable is connected between the port pair to be tested.

The analyzer is set to a series of CW frequencies across its full frequency

range. The analyzer’s trace statistics function is used to calculate the

standard deviation of both the magnitude trace and the phase trace.

These standard deviation values are reported as the analyzer’s trace noise

and are compared with the Trace Noise magnitude and phase

specifications.

If the Analyzer Fails this Test:
A failure of this test indicates a fault in the receiver’s IF chain between the

mixer and the A12 SPAM board. This can indicate a faulty assembly or a loose

cable.

— Check for proper torquing of all semi-rigid cables in the receiver chain, and

then repeat this test.

— If the analyzer still fails this test, replace the A12 SPAM board and repeat

this test. Most failures are due to this board. Refer to

“Removing and

Replacing the A4–A13 Boards” on page 7-15

— If the analyzer still fails this test, replace the mixer module for the failing

receiver, and then repeat this test.

Receiver Compression Test

Function of the Test: To measure the compression at the analyzer’s specified

maximum power level for the receivers.
Specification Tested: Test Port Input–Maximum Test Port Input Level
Equipment Used:

— U3070AK01 or Z5623A Option K01 Compression Test Set
— Power meter
— Power sensors

Содержание N5221A

















































































































































































































































































































































































Результаты поиска

Содержание N5221A

Отзывы:

Похожие инструкции для N5221A

Бренды по названию

Популярные бренды

Keysight Technologies N5221A, Руководство по обслуживанию

Результаты поиска

Содержание N5221A

Отзывы:

Похожие инструкции для N5221A

Бренды по названию

Популярные бренды