Omicron Lab Bode 100 Detailed Functional & Calibration Check Download

Page: 1 / 21

Smart Measurement Solutions

Bode 100 - Information

Detailed Functional & Calibration Check of

Bode 100

Table of Contents

CHECK OF FACTORY CALIBRATION

.............................................................................................................. 2

1.1

EST OF OUTPUT SIGNAL SHAPE

................................................................................................................................... 2

1.2

CCURACY OF OUTPUT FREQUENCY

............................................................................................................................. 4

1.3

CCURACY OF OUTPUT LEVEL

....................................................................................................................................... 6

1.4

CCURACY OF

AIN

HASE FACTORY CALIBRATION

.................................................................................................... 7

1.5

OISE FLOOR

HANNEL ISOLATION

........................................................................................................................... 10

1.6

CCURACY OF IMPEDANCE CALIBRATION

.................................................................................................................... 12

1.7

UICK CHECK OF ATTENUATORS

................................................................................................................................. 14

1.8

HECK OF ATTENUATOR CORRECTION

........................................................................................................................ 16

1.9

UICK CHECK OF

COUPLING CAPACITORS AT INPUT CHANNELS

................................................................. 18

1.10

HECK OF INTERNAL CONNECTIONS

OUTPUT IMPEDANCE

.................................................................................... 19

CALIBRATION SERVICE

................................................................................................................................... 20

By Bernhard Baumgartner & Tobias Schuster
© 2008-2020 by OMICRON Lab

– V4.0

Visit

www.omicron-lab.com

for more information.

Contact

[email protected]

for technical support.

Summary of Contents for Bode 100






















Search results

Summary of Contents for Bode 100

Reviews:

Related manuals for Bode 100

Brands by name

Popular brands

Omicron Lab Bode 100, Detailed Functional & Calibration Check

Search results

Summary of Contents for Bode 100

Reviews:

Related manuals for Bode 100

Brands by name

Popular brands