Keysight Technologies N5221A Скачать руководство пользователя

Страница: 36 / 368

3-8 Keysight N5221A/22A Service Guide

Tests and Adjustments
About System Verification and Performance Tests

Instrument Specifications

The analyzer's instrument specifications are described in the

Data Sheet and

Technical Specifications documents, available online at:

http://literature.cdn.keysight.com/litweb/pdf/N5221-90002.pdf

and

http://literature.cdn.keysight.com/litweb/pdf/N5221-90001.pdf

These specifications apply when the analyzer is used to make either raw or

error-corrected measurements.

System Verification Procedure

The system verification procedure tests the network analyzer measurement

“system”, as defined previously, against the system specifications. If

confirmation is successful, the measurement system is capable of making

measurements to the accuracy specified by the graphs of measurement

uncertainty.
The procedure consists of calibrating the analyzer with a calibration kit,

measuring a set of characterized devices, and comparing the resultant

measured data to the data and uncertainty limits supplied with the verification

kit. The device data provided with the verification kit has a traceable path to

NIST. The total measurement uncertainty limits for the performance

verification are the sum of the factory measurement uncertainties and the

uncertainties associated with measuring the same devices on the system being

verified. The difference between the factory-measured data and the

verification-measured data must fall within the total uncertainty limits at all
frequencies for the total system uncertainty test to pass.

Performance Tests

Performance tests are used to confirm analyzer performance against the

“instrument” specifications. If confirmation is successful, the analyzer meets

the instrument specifications.
Performance tests are contained in the analyzer’s firmware with Options 897 or

898 and are described at

“Performance Tests” on page 3-31

An illustrated outline of the performance verification procedure:

— for ANSI/NCSL Z540.3-2006 and ISO/IEC 17025 verification, is shown in

Figure 3-1 on page 3-10

— for non-standards verification, is shown in

Figure 3-2 on page 3-11

Calibration kits are different from verification kits. Calibration kits are used

to determine the systematic errors of a network analyzer measurement

system. Verification kits are used to confirm system specifications and are

not used to generate error correction.

Содержание N5221A

















































































































































































































































































































































































Результаты поиска

Содержание N5221A

Отзывы:

Похожие инструкции для N5221A

Бренды по названию

Популярные бренды

Keysight Technologies N5221A, Руководство по обслуживанию

Результаты поиска

Содержание N5221A

Отзывы:

Похожие инструкции для N5221A

Бренды по названию

Популярные бренды