Keysight Technologies N5221A Скачать руководство пользователя

Страница: 322 / 368

7-58 Keysight N5221A/22A Service Guide

Repair and Replacement Procedures
Removing and Replacing the Lithium Battery

Removing and Replacing the Lithium Battery

Tools Required

— T-10 TORX driver (torque to 9 in-lb or 1.02 N.m)
— T-20 TORX driver (torque to 21 in-lb or 2.38 N.m)
— ESD grounding wrist strap

Removal Procedure

Refer to

Figure 7-27

for this procedure.

Disconnect the power cord.

Remove the A17 CPU board. Refer to

“Removing and Replacing the A17

CPU Board Assembly” on page 7-25

Remove top cover attachment screws (item

①

) and (item

➁

Lift the top cover off of the CPU board assembly.

Remove the battery from the battery holder by lifting it at the open end of
the holder and then sliding it from under the clip (item

③

DO NOT THROW AWAY THE BATTERY. COLLECT IT AS SMALL CHEMICAL

WASTE. Refer to

“Lithium Battery Disposal” on page 1-10

for additional

information on battery disposal.

Replacement Procedure

Reverse the order of the removal procedure following all instructions

included with the new battery.

Perform the post-repair adjustments, verifications, and performance tests

that pertain to this removal procedure. Refer to

Table 7-2 on page 7-60

Содержание N5221A

















































































































































































































































































































































































Результаты поиска

Содержание N5221A

Отзывы:

Похожие инструкции для N5221A

Бренды по названию

Популярные бренды

Keysight Technologies N5221A, Руководство по обслуживанию

Результаты поиска

Содержание N5221A

Отзывы:

Похожие инструкции для N5221A

Бренды по названию

Популярные бренды