Keysight Technologies N5221A Скачать руководство пользователя страница 285 | Manualshive

Страница: 285 / 368

Keysight Technologies N5221A Скачать руководство пользователя страница 285

Keysight N5221A/22A Service Guide 7-21

Repair and Replacement Procedures
Removing and Replacing the A15 Midplane Board

Removing and Replacing the A15 Midplane Board

Tools Required

— T-10 TORX driver (torque to 9 in-lb or 1.02 N.m)
— T-20 TORX driver (torque to 21 in-lb or 2.38 N.m)
— 5/16 inch open-end torque wrench (torque to 10 in-lb or 1.13 N.m)
— ESD grounding wrist strap

Removal Procedure

Refer to

for this procedure.

1.

Disconnect the power cord.

2.

Remove the outer and inner covers. Refer to

“Removing the Covers” on

.

3.

Remove the A16 power supply assembly. Refer to

“Removing and

Replacing the A16 Power Supply Assembly” on page 7-23

4.

Remove the A17 CPU board assembly. Refer to

“Removing and Replacing

the A17 CPU Board Assembly” on page 7-25

5.

Remove six screws (item

①

) from the A15 midplane board.

6.

Lift the board ejectors (item

➁

) to the upright position to disengage the

A15 midplane board from the A14 system motherboard.

7.

Note the positions of the five rubber grommets (item

③

) on the bottom

three A15 midplane board alignment pins. Remove these rubber

grommets and retain them for reinstallation on the new A15 midplane

board.

8.

Lift the A15 midplane board out of the analyzer.

Replacement Procedure

1.

Reverse the order of the removal procedure.
Be careful to align the guide pins on the A15 midplane board connectors

with the slots on the A14 system motherboard connectors.
The board ejectors should be in the upright position when installing the

A15 midplane board. Align these ejectors with the slots in the chassis

inner panels as the board is lowered into position and then push them

down flat.
Remember to install the five rubber grommets on the bottom three

alignment pins: one on the alignment pin closest to the fans and two each

on the other two alignment pins.

2.

Perform the post-repair adjustments, verifications, and performance tests

that pertain to this removal procedure. Refer to

Table 7-2 on page 7-60

.

«
...
283
284
285
286
287
...
»

Содержание N5221A

















































































































































































































































































































































































Отзывы:

Нет отзывов