Keysight Technologies InfiniVision 6000L Series Скачать руководство пользователя страница 49

Страница: 49 / 100

Keysight InfiniVision 6000L Series Oscilloscopes

Service Guide

3 Calibrating and Adjusting

This chapter explains how to adjust the oscilloscope for optimum operating

performance. You should perform self-calibration according to the following

recommendations:
• Every 12 months or after 2000 hours of operation
• If the ambient temperature is >10 °C from the calibration temperature
• If you want to maximize the measurement accuracy

The amount of use, environmental conditions, and experience with other

instruments help determine if you need shorter adjustment intervals.

Let the Equipment Warm Up Before Adjusting

Before you start the adjustments, let the oscilloscope and test equipment warm

up for at least 30 minutes.

Read All Cautions and Warnings

Read the following cautions and warning before making adjustments or

performing self-calibration.

WARNING

HAZARDOUS VOLTAGES!

Read the safety notice at the front of this book before proceeding.

Maintenance is performed with power supplied to the oscilloscope and with the protective covers

removed. Only trained service personnel who are aware of the hazards involved should perform the

maintenance. Whenever possible, perform the procedures with the power cord removed from the

oscilloscope.

CAUTION

REMOVE POWER TO AVOID DAMAGE!

Do not disconnect any cables or remove any assemblies with power applied to the oscilloscope.

Otherwise, damage to the oscilloscope can occur.

Содержание InfiniVision 6000L Series





































































































Результаты поиска

Содержание InfiniVision 6000L Series

Отзывы:

Похожие инструкции для InfiniVision 6000L Series

Бренды по названию

Популярные бренды

Keysight Technologies InfiniVision 6000L Series, Руководство по обслуживанию

Результаты поиска

Содержание InfiniVision 6000L Series

Отзывы:

Похожие инструкции для InfiniVision 6000L Series

Бренды по названию

Популярные бренды