Keysight Technologies Infiniium MSOV 084A Скачать руководство пользователя страница 78

Страница: 78 / 164

Infiniium V-Series Oscilloscopes Service Guide

Troubleshooting

Front Panel LED Troubleshooting

If you see a failure with the on/off switch backlight LED, replace the On/Off board.

If the LED will still not illuminate, replace the motherboard and see if this fixes the

problem. If the LED still does not work, check the on/off cable connecting the

On/Off board to the motherboard, and check the connections of all cables on the

on/off board and the motherboard.
If any of the other LEDs on the front panel are not working, the first step is to

troubleshoot the acquisition assemblies to make sure they are working. If they are

working, replace the keyboard assembly and see if the LEDs will illuminate. If the

LEDs will not illuminate, the last step is to reload the oscilloscope software.
When reassembling the oscilloscope, be sure to reinstall all boards that were

replaced, but that were not causing the problem.

Содержание Infiniium MSOV 084A





































































































































































Результаты поиска

Содержание Infiniium MSOV 084A

Отзывы:

Похожие инструкции для Infiniium MSOV 084A

Бренды по названию

Популярные бренды

Keysight Technologies Infiniium MSOV 084A, Руководство по обслуживанию

Результаты поиска

Содержание Infiniium MSOV 084A

Отзывы:

Похожие инструкции для Infiniium MSOV 084A

Бренды по названию

Популярные бренды