Keysight Technologies E8364-60108 Скачать руководство пользователя страница 6

Страница: 6 / 32

Keysight E8363B/C and E8364B/C Installation Note 3

General Information
Items Included in the Upgrade Kit

Items Included in the Upgrade Kit

Check the contents of your kit against this list. If any item is missing or
damaged, contact Keysight Technologies. Refer to

“Getting Assistance from

Keysight” on page 1

Table 1

Contents of Option UNL Upgrade Kit (E8364-60108)

Ref.

Desig.

Description

Qty

Part Number

These parts are for all analyzers

Installation note (this document)

E8364-90025

Machine screw, M3.0 x 8 CWPNTX (for attaching attenuators)

0515-0372

Machine screw, M2.5 x 14 CWPNTX (for attaching bias tees)

0515-2141

Cable clamp

1400-1439

A36, A37

60-dB step attenuator

33325-60012

A38, A39

Bias tee (cable included)

5067-4812

Ribbon cable (for A36 step attenuator)

8121-0819

Ribbon cable (for A37 step attenuator)

8121-0119

W51

RF cable, A22 switch splitter to A36 step attenuator

E8364-20055

W52

RF cable, A22 switch splitter to A37 step attenuator

E8364-20056

W55

RF cable, A38 bias tee to A25 test port 1 coupler

E8364-20167

W56

RF cable, A39 bias tee to A26 test port 2 coupler

E8364-20168

These parts are for analyzers WITHOUT Option 014

RF cable, channel R1 attenuator to A28 channel R1 mixer

E8364-20174

RF cable, channel R2 attenuator to A29 channel R2 mixer

E8364-20175

W53

RF cable, A36 step attenuator to A38 bias tee

E8364-20077

W54

RF cable A37 step attenuator to A39 bias tee

These parts are for analyzers WITH Option 014 but WITHOUT Option 081

Lower front panel overlay (Option UNL/014)

E8364-80011

W70

RF cable, REFERENCE 1 RCVR R1 IN to A28 channel R1 mixer

E8364-20176

W71

RF cable, REFERENCE 2 RCVR R2 IN to A29 channel R2 mixer

E8364-20177

W81

RF cable, A36 step attenuator to PORT 1 SOURCE OUT

E8364-20053

W82

RF cable, A37 step attenuator to PORT 2 SOURCE OUT

E8364-20054

W83

RF cable, PORT 1 CPLR THRU to A38 bias tee

E8364-20039

W84

RF cable, PORT 2 CPLR THRU to A39 bias tee

E8364-20040

Содержание E8364-60108

































Результаты поиска

Содержание E8364-60108

Отзывы:

Похожие инструкции для E8364-60108

Бренды по названию

Популярные бренды

Keysight Technologies E8364-60108, Установочная инструкция

Результаты поиска

Содержание E8364-60108

Отзывы:

Похожие инструкции для E8364-60108

Бренды по названию

Популярные бренды