Keysight Technologies E4981A Скачать руководство пользователя

Страница: 114 / 152

112

Chapter 6

Replacement Procedure

Fan Assembly Replacement

Tools Required

•

Torque screwdriver, TORX T20

•

Cutting plier

•

Flat edge driver

Removal Procedure

Refer to

Figure 6-15

and for this procedure.

Step 1.

Remove the 3/4 rack module top as described in

“3/4 Rack Module Top Replacement” on

page 92

Step 2.

Remove the PSU Deck Assembly as described in

“PSU Deck Assembly Removale” on

page 95

Step 3.

Cut the two cable ties (item 1).

Step 4.

Remove a TORX T20 screw (item 2) fastening the ground cable.

Step 5.

Disconnect the fan cable from the A31 Digital Board Assembly (item 3).

Step 6.

Push the four rivets (item 4) from the inside, then remove them fastening the Fan
Assembly.

NOTE

If you cannot push the rivets out easily, push the rivets out using a flat-edge driver.

Step 7.

Remove the Fan Assembly.

Replacement Procedure

Step 1.

Reverse the order of the removal procedure.

NOTE

When you replace the Fan Assembly, use new rivets and cable ties.

Содержание E4981A

























































































































































Результаты поиска

Содержание E4981A

Отзывы:

Похожие инструкции для E4981A

Бренды по названию

Популярные бренды

Keysight Technologies E4981A, Руководство по обслуживанию

Результаты поиска

Содержание E4981A

Отзывы:

Похожие инструкции для E4981A

Бренды по названию

Популярные бренды