Keysight Technologies DSO-X 2014A Скачать руководство пользователя страница 314

Страница: 314 / 378

314

Keysight InfiniiVision 2000 X-Series Oscilloscopes User's Guide

Reference

Upgrade model numbers with the "A" suffix are subscription-based licenses; the

ones with the "B" suffix are perpetual licenses.

Other Options Available

Upgrading to an MSO

A license can be installed to activate the digital channels of an oscilloscope that

was not originally ordered as a mixed-signal oscilloscope (MSO). A mixed signal

oscilloscope has analog channels plus 8 time-correlated digital timing channels.

For information about upgrading your oscilloscope through licensing, contact your

local Keysight Technologies representative or see

www.keysight.com/find/2000X-Series

Software and Firmware Updates

From time to time Keysight Technologies releases software and firmware updates

for its products. To search for firmware updates for your oscilloscope, direct your

web browser to

www.keysight.com/find/2000X-Series-sw

RML

Remote Command Logging

Now standard.

SGM

Segmented Memory.
Lets you capture infrequent or burst signals with great

resolution by eliminating the capture of your signal's

"inactivity".

Order DSOX2PLUS (includes previous

DSOX2SGM).

WAVEGEN

Waveform Generator.

Order DSOX2WAVEGEN.

Table 4

Licensed Options Available (continued)

License

Description

After purchase model number, notes

Table 5

Calibration Option

Option

Order

A6J

ANSI Z540 Compliant Calibration

Содержание DSO-X 2014A



























































































































































































































































































































































































Результаты поиска

Содержание DSO-X 2014A

Отзывы:

Похожие инструкции для DSO-X 2014A

Бренды по названию

Популярные бренды

Keysight Technologies DSO-X 2014A, Руководство пользователя

Результаты поиска

Содержание DSO-X 2014A

Отзывы:

Похожие инструкции для DSO-X 2014A

Бренды по названию

Популярные бренды