Keysight Technologies DSO-X 2014A Скачать руководство пользователя страница 282

Страница: 282 / 378

282

Keysight InfiniiVision 2000 X-Series Oscilloscopes User's Guide

Utility Settings

If the ground level is off screen, the waveform will expand about the top or

bottom edge of the screen based on where the ground is off screen.

•

Center

— The displayed waveform will expand about the center of the display.

To disable/enable transparent backgrounds

There is a preference setting for whether measurements, statistics, reference

waveform information, and other text displays have transparent or solid

backgrounds.

Press

[Utility] > Options > Preferences

Press

Transparent

to toggle between transparent and solid text display

backgrounds.

To load the default label library

See

"To reset the label library to the factory default"

on page 135.

To set up the screen saver

The oscilloscope can be configured to turn on a display screen saver when the

oscilloscope has been idle for a specified length of time.

Press

[Utility] > Options > Preferences > Screen Saver

to display the Screen Saver

Menu.

Press the

Saver

softkey to select the screen saver type.

The screen saver can be set to

Off

, to display any of the images shown in the

list, or can display a user-defined text string.

User

is selected, press the

Spell

softkey to select the first character of the text

string. Use the Entry knob to choose a character. Then press the

Enter

softkey

to advance to the next character and repeat the process.

NOTE

You can use a connected USB keyboard instead of using the

Spell

(and other) character

editing softkeys.

Содержание DSO-X 2014A



























































































































































































































































































































































































Результаты поиска

Содержание DSO-X 2014A

Отзывы:

Похожие инструкции для DSO-X 2014A

Бренды по названию

Популярные бренды

Keysight Technologies DSO-X 2014A, Руководство пользователя

Результаты поиска

Содержание DSO-X 2014A

Отзывы:

Похожие инструкции для DSO-X 2014A

Бренды по названию

Популярные бренды