Keysight Technologies DSO-X 2014A Скачать руководство пользователя страница 135

Страница: 135 / 378

Labels

Keysight InfiniiVision 2000 X-Series Oscilloscopes User's Guide

135

Use a text editor to create each label. Each label can be up to ten characters in

length. Separate each label with a line feed.

Name the file labellist.txt and save it on a USB mass storage device such as a

thumb drive.

Load the list into the oscilloscope using the File Explorer (press

[Utility] > File

Explorer

To reset the label library to the factory default

Press

[Utility] > Options > Preferences

Press the

Default Library

softkey.

This will delete all user-defined labels from the library and set the labels in the

library back to the factory default. However, this does not default the labels

currently assigned to the channels (those labels that appear in the waveform

area).

NOTE

Label List Management

When you press the

Library

softkey, you will see a list of the last 75 labels used. The list does

not save duplicate labels. Labels can end in any number of trailing digits. As long as the base

string is the same as an existing label in the library, the new label will not be put in the library.

For example, if label A0 is in the library and you make a new label called A12345, the new

label is not added to the library.
When you save a new user-defined label, the new label will replace the oldest label in the list.

Oldest is defined as the longest time since the label was last assigned to a channel. Any time

you assign any label to a channel, that label will move to the newest in the list. Thus, after you

use the label list for a while, your labels will predominate, making it easier to customize the

instrument display for your needs.
When you reset the label library list (see next topic), all of your custom labels will be deleted,

and the label list will be returned to its factory configuration.

NOTE

Pressing the Default Library softkey will remove all user-defined labels from the library and

set the labels back to the factory default. Once deleted, these user-defined labels cannot be

recovered.

Содержание DSO-X 2014A



























































































































































































































































































































































































Результаты поиска

Содержание DSO-X 2014A

Отзывы:

Похожие инструкции для DSO-X 2014A

Бренды по названию

Популярные бренды

Keysight Technologies DSO-X 2014A, Руководство пользователя

Результаты поиска

Содержание DSO-X 2014A

Отзывы:

Похожие инструкции для DSO-X 2014A

Бренды по названию

Популярные бренды