Keysight Technologies DSO-X 2014A Скачать руководство пользователя страница 230

Страница: 230 / 378

230

Keysight InfiniiVision 2000 X-Series Oscilloscopes User's Guide

Mask Testing

Run Until

The Run Until softkey lets you specify a condition on which to terminate testing.

• Forever

— The oscilloscope runs continuously. However, if an error occurs the

action specified using the

On Error

softkey will occur.

• Minimum # of Tests

— Choose this option and then use the

# of Tests

softkey

to select the number of times the oscilloscope will trigger, display the

waveform(s), and compare them to the mask. The oscilloscope will stop after

the specified number of tests have been completed. The specified minimum

number of tests may be exceeded. If an error occurs the action specified

using the

On Error

softkey will occur. The actual number of tests completed

is displayed above the softkeys.

• Minimum Time

— Choose this option and then use the

Test Time

softkey to

select how long the oscilloscope will run. When the selected time has passed

the oscilloscope will stop. The specified time may be exceeded. If an error

occurs the action specified using the

On Error

softkey will occur. The actual

test time is displayed above the softkeys.

• Minimum Sigma

— Choose this option and then use the Sigma softkey to

select a minimum sigma. The mask test runs until enough waveforms are

tested to achieve a minimum test sigma. (If an error occurs the oscilloscope

will perform the action specified by the

On Error

softkey.) Note that this is a

test sigma (the max achievable process sigma, assuming no defects, for a

certain number of tested waveforms) as opposed to a process sigma (which is

tied to the amount of failures per test). The sigma value may exceed the

selected value when a small sigma value is chosen. The actual sigma is

displayed.

Содержание DSO-X 2014A



























































































































































































































































































































































































Результаты поиска

Содержание DSO-X 2014A

Отзывы:

Похожие инструкции для DSO-X 2014A

Бренды по названию

Популярные бренды

Keysight Technologies DSO-X 2014A, Руководство пользователя

Результаты поиска

Содержание DSO-X 2014A

Отзывы:

Похожие инструкции для DSO-X 2014A

Бренды по названию

Популярные бренды